|
|
|
|
Encapsulated
Thermostats for Electronics
|
ADVANTAGES
The miniature size, high switching capability and
versatility of its contacts make the JEDEC TO-220
compatible device ideal for printed circuit board
mounting. The F11-E06 is epoxy sealed to withstand
wave soldering and board washing operations.
APPLICATIONS
The F11-E06 is ideal to sense the temperature of
a surface or of stagnant air in an enclosure and
can be supplied for mounting on a printed circuit
board or with flexible wire leads for remote installation.
Its high temperature resistance and high dielectric
strength make it the favored device for protecting
heatsinks. Heat sensitive semiconductors and other
valuable equipment can be saved from thermal damage
by shutting down the power or simply turning on
a fan. Power Supplies,
Power Semi-Conductors, Electronic Ballasts, Fluorescent
and HID Ballasts, Motor and Transformer Protection
DESCRIPTION
The CANTHERM F11-E06 has been designed to protect
today’s technology and meet the requirements
of tomorrow’s innovations. The F11 snap action
bimetallic element will respond rapidly and accurately
to changes in the temperature of the surface to
which it is mounted or the air temperature in an
enclosure. The single pole, single throw contacts
can be configured as either normally open or normally
closed, operating on rise in temperature. The average
automatic reset will occur at a temperature approximately
20 - 25°C below the calibrated set point. The
housing has been designed for demanding conditions
such as high continuous temperatures and high voltage
electrical isolation. The “New” PC version
is now available with TO-220 style stamped lead-frame
leads and are shipped in a 50 piece plastic magazine
for ease of insertion and handling.
|
F11-E06 >
Online Tech Info
 The
Cantherm F11-E06 Encapsulated Thermostat for Electronics
is now available with die cut PCB leads. JEDEC TO-220
critical dimensions, such as lead spacing, lead to
back plane and board to mounting hole, have been respected
to insure interchangeability. They will be shipped
in 50 piece plastic tube magazines for ease of handling
and loading for automatic insertion. Because of the
plastic TO-220 style housing high voltage and high
temperature applications (4000 VAC dielectric @ 200°C)
can be achieved. The RYTON PPS plastic is UL94 V-0
approved and withstands long-term exposure to 220°C.
Available with N/C or N/O contacts, PC mounting pins
or flying leads in temperatures from 70°C to 160°C,
the F11-E06 is suitable for most applications. Its
small size and 3 amp current rating makes them ideal
for today’s smaller higher watt density designs.
F11-E06
>
PDF Tech Info, Schematics and More |
OPERATING TEMPERATURES
The F11-E06 is available from 65°C to 160°C
with either normally closed or normally open contacts.
Increments are 5°C and standard tolerance is ±5°C.
CONNECTIONS
The F11-E06 is available for PC board mount or a
variety of flexible wire leads. Standard leads are
6”, 24 AWG UL3266 Black up to 125°C and
UL1180 Teflon up to the maximum temperature. ADD “-PC”
to the part number for solid pins or specify flexible
lead type. Other wire types, gauges and lead lengths
available upon request. |
| TYPE |
N/C |
N/O |
Voltage
Rating 50-60 Hz |
120
V / 250 V |
120
V / 250 V |
Current
rating RESISTIVE
INDUCTIVE |
3.0
A / 2.0 A
1.8 A / 1.2 A |
1A
/ 1 A*
1A / 1 A
|
max.
load RES.
short circuit current upto |
4.0
A
6.3 A |
4.0
A
6.3 A |
Contact
Arrangement Normally closed N/C
Normally open N/O |
|
|
Contact
resistance |
<
40mΩ |
<
40mΩ |
Response
temperature range |
70°C
to 160°C |
+65°C
to +150°C |
Tolerance
(minimum range) |
±15°C,
±10°C, ±5°C |
±15°C,
±10°C, ±5°C |
Max.
permanent temperature - housing
Swith mechanism |
220°C
**
175°C |
220°C
**
175°C |
|
| F11-E06-PC |
|
|
F11-E06 |
|
CURRENT SENSIVITY
The thermostats are not current sensitive at rated
currents. At loads above the rated values, up to maximum
loading there is self-heating of the current carrying
contacts.
*
When N/0 contacts are closed, self heating will occur
at currents exceeding normal rating. It is possible
that, given certain combinations of set temperature
current & ambient temperature, the contacts will
not reset.
** Wire insulation must be appropriate
INSULATION RESISTANCE
| Leads
to Earth |
2500
V @ 25°C
1500 V @ 100°C |
On
request
(Requires special testing) |
up
to 4000 V eff. AC @ 200°C |
Across
open contacts,
dependent on response
temperature |
500
V eff. AC |
RESPONSE TEMPERATURES, TOLERANCE
Temperature stepped in 5°C increments. Special
switch-off and reset temperatures available on request.
Rate of temperature rise from 0.1° C/min. to max.
1.0° C/min. Insulation of the housing will slow
down the cutout’s response.
|
QUALITY ASSURANCE
Housing material - PPS (UL 94 V-0)
Contacts - Silver plated
MTBF - 10,000 cycles at rated current and voltage
Minimum switching current 50ma
Random sample quality testing
Function test to AQL 1.0
Nominal response temperature AQL 1.0
Measurement tolerance ±2°C AQL 4.0
Other values AQL 4.0
Thermal conductivity - 4.0 BTU In/hr/Ft2/ºF
ORDERING
INFORMATION
| Quantity |
Type |
Response
Temp. |
Version
N/O or N/C |
Tolerance
+/- 5°C |
| 100 |
F11 |
125° |
1
or 2 |
5 |
We
reserve the right to change specifications without
prior notice. ADD - PC to part number for PC lead
frame leads.
Typical PC P/N = F11125253600060
With Leads P/N = F1112525ACFA06E
UL
E46827
VDE 4523-4510-1015
It is the responsibility of the customer to insure
that the devices descibed above are used in a safe
manner and within published parameters.
RoHS compliant product |
|
8415
Mountain
Sights Avenue, Montreal (Quebec), H4P 2B8 Canada
